[tp widget="default/tpw_default.php"]

how to fit laminate flooring around radiator pipes

0 Comments 01:12

how to fit laminate flooring around radiator pipes插图

Can you cut laminate flooring around a radiator pipe?

Neatly cut down these lines with a fine-tooth saw and fit the plank around the radiator pipe. Cutting laminate flooring like this can be tricky, so be careful. Once you’ve put the plank in place, push the wedge back in with some glue to secure it in place.

How to fit floorboards around radiator pipes?

Here is a very quick guide on how to fit your floorboards around radiator pipes. Step 1: Carefully measure and mark the position of the pipe. Step 3: Mark out a 15 wedge. Step 4: Cut neatly down the lines with a fine tooth saw. Step 5: Push the wedge back in and file to circle again.

How to install laminate flooring behind pipes and walls?

Use tape to fasten everything. Place the laminate floor up against the tubes. Use a slat to draw the distance between the pipes and wall. Measure the distance from the centre of the tubes. This piece of flooring will be placed against the wall, behind the tubes.

Can you drill a hole in hardwood floor for radiator pipe?

It can be tempting when fitting a hardwood floor to drill a hole that is the perfect size for a radiator pipe to pass through. The finish will look good and you won’t have to cover any rough edges or hide the hole in any way. However, this can be a big mistake.

Why do you need to leave an expansion gap around a floating floor?

This is due to changes in the floor’s size over the course of a year such as expansion and contraction in response to the changing atmosphere in a room.

Can you leave an expansion gap around a radiator?

However, this can be a big mistake. An expansion gap should always be left around radiator pipes so the floor can move. If the floor moves a lot and the hole you have drilled is not big enough, the pipe can burst in extreme situations. Most radiator pipes are 15mm in diameter so using a 25mm hole saw should suffice.

Can you cut around radiator pipes?

The finish will look good and you won’t have to cover any rough edges or hide the hole in any way. However, this can be a big mistake.

What is the best flooring to put in a home?

There are several ways to give your home a facelift and one is to install hardwood flooring. Hardwood flooring is a premium addition to any home and will add both aesthetic and financial value. Not only does it look great, but it is very durable and can come in a variety of options from oak to cherry.

Why do you use T molding?

T-molding is one of the most common transitions in doorways, and is also used to join hardwood floors in large areas due to expansion gaps caused by expansion and contraction. With those gaps filled and the above obstacles cleared, you’ll be well on your way to giving your home’s floor a stunning facelift.

Can you install hardwood floors yourself?

You can easily install solid hardwood flooring yourself, without experience. Even in condos, basements and over concrete!

Can you put hardwood flooring under a radiator?

An alternative will be to jack it up enough for you to slip the hardwood flooring underneath. Another work-around is to mark a rectangular perimeter encasing the base of the radiator, and using it to install the flooring around your home’s heating system.

Is it easier to install hardwood?

Installing your own solid hardwood is easier than you think. But how much will it really cost?

Can you lay wood around a radiator?

An SFGATE article on laying wood floors around a radiator notes that the process will, in most cases, require you to remove the radiator first, especially if it is a cast-iron one.

Who is Ashley Marks?

Ashley Marks is a blogger with a passion for renovating property. One aspect she likes to focus on is the financial side of renovating , and she hopes her blog posts can help readers avoid the common financial pitfalls of changing their property for the better. When she isn’t writing, she can be found spending time with her husband and two children.

Edinburgh22 New Member

Hi there, I’m fitting laminate in one of my rooms, and the radiator pipes enter the floor at an angle (not 90° I’m afraid – see picture attached).

Mark Griffiths Member

Further complicated by the fact that the floor board needs to be installed at angle to click in with the existing board.

I-Man Screwfix Select

This is one of those situations where you can never really get a nice neat finish, as you need to make such a large cutout. How about simply boxing in around the bottom of the radiator? Not quite as drastic a step as what above suggested

CGN Screwfix Select

Hi there, I’m fitting laminate in one of my rooms, and the radiator pipes enter the floor at an angle (not 90° I’m afraid – see picture attached).

cleggie Active Member

why not just redo the pipe.Cut it near the wall then a 90 elbow to bring it up then just use a couple more elbows and pipe..All you need then is a little cut out in laminate where pipe is at wall.Much easier and neater and not difficult at all

Mr Rusty Screwfix Select

Cut a hole in the laminate that matches where the outer face of the pipe will come through the board. From the hole cut a wedge shaped piece about twice the pipe width at the skirt side – or a tad wider. You will end up with a cheese shaped piece with the remains of the hole at the tip.

Edinburgh22 New Member

Thanks everyone! At the end I did what Mr Rusty said (see last pic of bottom of wedges) – it took a LOT of filing, but it kind of looks okay. The shape of the holes could be a little bit nicer, but I can always file it down a little bit more. In hindsight, oval holes would have been nicer.

How to write an outline on paper?

Scribe the outline with a compass or scribing tool. Splay the two arms of the tool. Lock them so the angle can’t change, then follow the outline of the foot with the compass or scribe point while the pencil on the other arm traces the outline on the paper.

How to draw a radiator?

1. Draw a rectangle around the base of the radiator with a carpenter’s square and a pencil. If the radiator is next to the wall, extend the rectangle to the wall as well.

How to hide the notches on a radiator?

You can hide the notches, or the entire underside of the radiator — if you constructed a frame — by constructing a 4- or 5-inch skirting board for the bottom of the radiator.

What degree does Chris Deziel have?

Chris Deziel has a bachelor’s degree in physics and a master’s degree in humanities. Besides having an abiding interest in popular science, Deziel has been active in the building and home design trades since 1975. As a landscape builder, he helped establish two gardening companies. Related Articles.

How to stop wood chipping?

Cut along the outline with a jigsaw and metal cutting blade, which prevents wood chipping. If the shape is entirely enclosed by wood, you’ll have to extend it all the way to the grooved side of the board to be able to tap the board in place.

How to cut a foot on a board?

Measure the exact position of the foot on the next board you’re going to install, using a tape measure, and make a mark. Cut out the shape you traced, using scissors, center it on the mark and outline it on the wood. Cut along the outline with a jigsaw and metal cutting blade, which prevents wood chipping. If the shape is entirely enclosed by wood, you’ll have to extend it all the way to the grooved side of the board to be able to tap the board in place.

Can you raise a radiator and put flooring underneath?

Warnings. It is definitely preferable to raise the radiator and install the flooring underneath it, but if the plumbing won’t allow you do do this, don’t force it. You could rupture a pipe joint and cause a leak that you can’t see. Writer Bio.

Related Post