[tp widget="default/tpw_default.php"]

how to fit a register plate

0 Comments 12:20

how to fit a register plate插图

Sit the flexible liner into the adapter and make sure it is located centrally. Tighten the adapter to hold the liner in position and to secure the adapter to the liner. The registerplate can now be fitted into the steel frame. The offcut of the stove pipe can be used as a template by drawing a line round it.

How do you fit a register plate to a steel frame?

Tighten the adapter to hold the liner in position and to secure the adapter to the liner. The register plate can now be fitted into the steel frame. The offcut of the stove pipe can be used as a template by drawing a line round it. This circle can be cut out using a jig saw for example.

How do you install a register plate on a stove?

Sit the flexible liner into the adapter and make sure it is located centrally. Tighten the adapter to hold the liner in position and to secure the adapter to the liner. The register plate can now be fitted into the steel frame. The offcut of the stove pipe can be used as a template by drawing a line round it.

When should a register plate be fitted to a chimney?

A Register Plate should always be fitted whenever a stove vents directly into the chimney (ie if the chimney is sound and there is no flue liner connected directly to the stove or stove pipe). The purpose of this register plate is to ensure no fumes, especially Carbon Monoxide, escapes back into the room.

What is the difference between a closure plate and register plate?

A closure plate and a register plate are not the same. A register plate is used when a chimney has no stainless steel liner. It closes off the chimney at its base, just above a wood burning stove.

What size register plate should I use for a woodburning stove?

Yup. Pretty standard stuff. Register plate for a woodburning stove. The plate is a ~1-2mm plate. I think I’m going to give up on the brackets, cut the register plate into a sort-of cross, then fold the arms of the cross down and fasten those to the sides of the chimney, which, as the chimney is wide but shallow, I can drill into.

Do you need to notify BCO of stove fitting?

You need to notify bco if your fitting the stove yourself, there are a few guidelines to follow.

Does Hetas fit register plates?

If you use a Hetas registered installer, they sort it all out for you, plus will fit the register plate, it needs fitting properly plus you need access for sweeping flue.

Do you need a hammer for a blue Bosch drill bit?

Use one of those 90 degree attachments and blue Bosch multi drill bit – you won’t need hammer.

What is a register plate?

First off, let’s begin by looking at register plates. A register plate is a flat metal sheet that closes off the base of a chimney (it looks a bit like a ceiling above the main fireplace). It’s put in place when you are installing a stove within an existing fireplace.

Do you have to use a register plate or a closure plate?

If you are going to be using your stove without a chimney flue liner, then under the Building Regulations you have an obligation to fit an appropriate register plate.

What size register or closure plate do you need?

Once you’ve figured out whether you need a register plate or a closure plate to go with your stove, you need to make sure you buy the correct size register/closure plate.

What does a sealing plate do on a stove?

A sealing plate will protect the closure plate from the heat of the stove pipe as it passes through it and will also block up any gaps (the hole in the closure plate is usually a few inches wider in diameter than the stove pipe – so without a sealing plate you’d be left with an unsightly gap).

How long does a 316 flue liner last?

This 6-inch 316 grade flue liner is constructed from two individual strips of 316 stainless steel. It also comes with a 15-year guarantee compared to the 10 years that you get with other brands of chimney flue liner.

What is a closure plate made of?

Closure plates can be made from any non-combustible material. Many people choose to make their closure plates from cement board – made from a combination of cement and reinforcing fibres. Cement board can be painted with acrylic paint, so will help your fireplace blend in with the rest of your room.

Why do you need a closure plate?

Therefore, a closure plate is more for aesthetic reasons – to seal up the base of the chimney cavity where the flue goes up into the chimney.

Why do you need a register plate for a chimney?

The purpose of this register plate is to ensure no fumes, especially Carbon Monoxide, escapes back into the room. The Register Plate must therefore be sealed around the edges and around the stove pipe. The Register Plate must also have an access hatch to enable the chimney to be swept.

What is the name of the plate on a wood burning stove?

The plate must be made of solid, non-combustible material. You may hear this plate referred to as a “Closure” or “Register” plate. Although these terms are often used interchangeably by some people, there is an important difference between them.

Do register plates need to be sealed?

The Register Plate must therefore be sealed around the edges and around the stove pipe. The Register Plate must also have an access hatch to enable the chimney to be swept. Closure Plate. A Closure Plate performs a different purpose.

Do you need a closure plate for a stove?

Because the stove is directly connected to the flue liner, the Closure Plate is not required to be tightly sealed in the same way as a Register Plate; it also does not need an access hatch for sweeping as this will take place either through the stove or, where fitted, through a removable sweeping plate on the stove pipe.

What is a closure plate made of?

A closure plate can be made of any non-combustible material. In the picture on this page the closure plate is made of 12mm Hardiebacker concrete board which is arguably much easier to cut than metal. Hardiebacker available from Travis Perkins/B&Q etc. about £12 a sheet 1.2m x 0.8m.

Why do you need a closure plate on a chimney?

The closure plate is therefore only required to seal the chimney for cosmetic reasons, to stop soot old soot falling on the stove but also to stop heat disappearing up the chimney and being wasted.

What is the plate around the stove pipe?

Note that the small square plate around the stove pipe is our sealing plate (included in our liner fitting pack ).

What does it mean when a wood stove is efficient?

Modern wood burners are highly efficient and this means that LESS heat goes up the chimney. It is the heat that gives the draft (hot air rises and the hotter then the faster it rises). The more efficient the stove the less heat is wasted up the chimney and the more likely that a liner, rather than a cold void, will be what …

What is a register plate?

A register plate is used when a chimney has no stainless steel liner. It closes off the chimney at its base, just above a wood burning stove. It acts as a barrier to prevent the smoke and fumes in the chimney entering the room.

What happens if a register plate fails?

Well if a register plate failed then smoke could enter the room. This could happen, for example, if a brick fell from inside of the chimney. A register plate will usually have access doors to allow the sweep to access any chamber above it to remove fallen soot.

Who owns the stove fitter’s warehouse?

Stovefitter’s Warehouse is owned and managed by Julian Patrick, blogger and author of The Stove Fitter’s Manual. Julian was previously a full-time installer of wood burning stoves (including solid fuel heating systems). He laid down the tools in 2013 to write his stove manual and open a small shop in North Wales (the Wood Stove Hut, soon to grow into The Stovefitter’s Warehouse).

What Does A Register Plate Do?

A register plate or closure plate is installed at the base of a chimney for a number of reasons:

Does A Register Plate Have To Be Sealed?

A register plate (needed where the stovepipe discharges directly into the chimney with no flue liner) must be sealed to ensure that byproducts of a fire in your stove don’t return into your home once vented out of the stovepipe.

Why do you need a register plate on a fireplace?

Both register plates and closure plates need to be made from metal to help prevent damage to the stove or fireplace if an item such as brick falls down from the inside of the chimney.

What is a register plate for a wood burning stove?

What Is A Register Plate For Wood Burning Stoves? A register plate is a metal sheet that fits across the base of your chimney, just above where a stove would be installed. A register plate can also be referred to as a chimney register plate or stove register plate, as they are commonly installed as part of the installation …

Why are closure plates more common than register plates?

Closure plates can be more common than register plates because many stove installs include a flue liner to help with draw on the stove.

How to maximize draw on stove?

To help maximize the draw on the stove by providing a smaller channel for waste air to go through. When the stovepipe is venting directly into the chimney and there’s no flue liner, to ensure no waste gases from the fire escape back into the room.

Why can’t smoke enter a home if a closure plate fails?

Even if a closure plate fails then waste smoke and gases from a fire will can’t enter your home because they will still be sealed within the flue.

Related Post