How do you cut a pool blanket to fit?
If you have a freeform pool and need to cut the blanket to fit, the best way to do it would be to have a few people help you stretch the cover out taut over the pool and place weights around the cover to help hold it in place.
How do you install a solar blanket for a pool?
If your pool is rectangular, round, or oval and you were able to find a solar cover that is your exact pool size, then the job of installing your solar blanket is pretty quick and easy – just lay the cover on the pool with the bubbles facing down on the water and the smooth side facing up toward the sky.
How do I install a swimming pool cover?
1. Remove all swimming pool ladders and handrails. 2. Measure the pool and the pool cover. This will determine the overlap of the cover. Take the difference in width and length and divide by two. The overlap can vary from 10 to 15 inches. 3. Place cover over the pool carefully so you do not snag or damage the pool cover.
Do I need a pool roller or a pool blanket?
Tip: If you are heating your pool with a heater, a pool blanket is a must! All types of pool covers benefit your pool as they all reduce evaporation, reduce chemical loss, and reduce cleaning time by preventing leaves and debris from easily entering the pool. To keep it simple, if you have a pool cover, then you should have a pool roller.
How much does pool cover cost?
Effective and low priced—depending on your pool size, they can cost anywhere from $566-$1300— and they’re the perfect option for pool owners who keep a strict budget.
What is a Micron and the rule of thickness?
A micron is basically a millionth of an inch. Pool covers come in a variety of sizes and the thickness of the material is measured in microns. For example, a 600 micron cover is thicker than a 500 micron cover. While the variation between a 400 and a 500 micron blanket is slight, the price difference and features can be significant! The thicker the blanket, the more effective it is. Pool covers are available in several thickness variants so choose the best one that fits you needs and budget!
Why is 525 micron pool cover good?
525 micron covers also have a 10 year warranty period to give that peace of mind.
How thick should a pool cover be?
These swimming pool covers are a good thickness. The 400 micron thickness is usually the recommended starting point for a quality pool cover. This is the Goldilocks level in pool covers, not too thin, not too thick, just right.
What happens if you take off a pool cover?
Increase the lifespan of your cover – If you take off a pool cover manually, there’s a good chance that it’s going to get dragged over rough ground, rocks etc., and thereby possibly get scraped or torn on the side of the pool or surroundings.
How long does it take to get a pool cover off?
Keep your life easy! The point is, with a roller, getting a pool cover on and off is a breeze – the whole operation takes less than a minute. Without a roller you will be in a world of pain trying to fold, lift and store it. Not only is there a lot of material in these, they are wet, and heavy!
What does less cleaning mean in a pool?
Less cleaning = less pool cleaning chemical costs. Reduces evaporation of your pool’s water, less evaporation means less water costs. You’ll never know when you’re in the mood for an early morning swim. Pool covers will make sure that you won’t be in a (cold) shock first thing in the morning!
How thick is a solar pool cover?
Solar pool covers are available in various thicknesses, measured in thousandths of a millimeter, which you will usually see shortened to “mil.”. The higher the mil, the thicker the cover, and the more heat the cover will be able to retain in the pool. In The Swim carries 8 mil, 12 mil and 16 mil solar blankets.
How long does it take to get a solar blanket for a pool?
You will still have to cut it to fit if you have a freeform pool. Custom solar blankets can take three to four weeks for delivery. You may consider using two smaller solar blankets to cover larger pools.
What is a solar cover?
Image by Pegasus-Products.com. Solar covers are available in round, oval, or rectangular shapes of various sizes. You may think of oval and round solar covers as being for above ground pools and rectangular solar covers being for in ground pools, but in some cases you may be better off purchasing an oval or round cover for your in ground pool …
How to determine what size solar pool cover to buy?
To determine which size solar pool cover is best you really just need to measure the longest and widest points of the pool to ensure you purchase a cover that you can cut to fit if necessary but will still be able to cover the whole pool.
Can you cut a blanket for a freeform pool?
Nothing too heavy or sharp of course, you don’t want to damage the cover, or the pool, if a cinder block fell in, …
Can you throw out an old pool cover?
Also, don’t throw out your old cover right away when you order a new one, if you have the space in your yard, you may find it easier to use your old cover as a template by laying it on top of the new one and cutting around it rather than placing the cover over the pool. Some pool owners (for example those with an “L” shaped pool) …
How to protect pool cover from UV rays?
It will help if the cover stays in perfect condition for a long time to reflect the value of your money. For instance, you can use solar blanket reels to protect the blanket from intense UV rays. In that case, you’ll need to learn How to install solar blanket pool cover to reel to prevent it from pinching and folding. Folds can easily result in torn parts. It will also help if you know How to attach solar cover to reel for above ground pool.
How to keep solar blanket in place?
To keep your solar cover in place even during strong winds, you can: ? Use anchors that attach to the cover. ? Use a heavy pool cover. ? Place weights on the excess material. Using anchors attached to the cover is the best option as it keeps the blanket firm, even in the strongest winds.
How to keep a solar pool from blowing?
Trees and buildings help in reducing the speed and strength of fast-blowing winds. If you’re protecting your pool from debris, using weights on the cover will suffice to keep it from blowing away. Sturdy and heavy solar pool covers can withstand mild winds on their own.
Why do you need a solar pool cover?
Another top benefit of solar pool covers is that they prevent water loss through evaporation by up to 80%. The last thing you want is refilling the pool every time you need to have a good time. It can also help you save on water bills, especially during summer.
How long does it take for a pool cover to heat up?
Most pool covers will come in transparent fabric, but some are black to enhance maximum absorption of heat energy. It is essential to note that a well-covered pool will take about 12 hours to increase the water’s temperature by 5 degrees.
Do you need a professional to install a freeform pool?
Installation on a Freeform Pool. A freeform pool will require more work compared to standard shapes. You might want to hire a professional since the cover needs to stretch out to all corners of the pool. It may be beneficial to get a swimming pool expert or a knowledgeable handyman to help with this installation.
Do solar pool covers work?
Solar pool covers stack up to regular covers in ways that make them the best option. Besides being cost-friendly, solar pool covers also warms the pool water. Their design traps heat beneath, especially during high solar intensity. That means you don’t have to heat your pool with electric coils unless it’s winter.
If you have questions about your inground swimming pool cover installation at any time please feel free to give us a call at 1-800-515-1747 or send us an email, [email protected]
What are pool anchors made of?
The two-piece anchors are made from extra tough brass that is guaranteed never to rust or corrode. To add a more attractive appearance to your deck, your swimming pool cover will include a set of brass flanges that install on the anchor. These flanges will add a touch of class to your anchor points.
What is included in a pool cover?
The hardware consists of TruSteel springs and covers, brass anchors and flanges, TruSteel D-Rings, and a stainless steel ladder lock.
How long does it take to install a pool cover?
Installing your own safety pool cover is an easy DIY project, and takes only a few hours to complete.
What are the springs on a pool cover made of?
This allows for a long lifespan of your swimming pool cover. The Springs Ladder Locks are made from stainless steel to eliminate rust and corrosion. These springs hold the weight of your inground pool cover while at the same time, allows the pool cover to flex. This result allows for your cover to flex under the most extreme weather conditions which allow for years of worry-free operations. The included D-rings are zinc dipped steel preventing rust and ensuring structural integrity. The two-piece anchors are made from extra tough brass that is guaranteed never to rust or corrode.
How much conduit do I need for a deck?
For Brick, Pavers, Stone (or for wood decks less than 1-5/8″) to be installed, you will need a 3/4″ I.D. conduit or pipe that is 15″ in length. Drill into the deck using a rotary hammer drill with an appropriate size masonry bit. Vacuum or flush out the concrete dust in the bottom of the hole.
How to make sure anchors are straight?
After the cover has the initial anchors, layout the remaining straps (18″ from the edge of the cover). On rectangles, you can use a chalk line to make sure the anchors are in a straight line.
What is a winter cover for a pool?
A winter cover is designed to protect the pool during the winter months when many above ground pools are not in use. It is basically a tarp with grommets around the perimeter and comes with a cable and winch to hold it in place.
What are the different types of covers for above ground pools?
There are three main types of covers available for above ground pools: winter covers, leaf nets, and solar blankets. Please click here to view the Above ground pool covers. Comments. Email Guide.
How to secure a pool cover?
With your cover (s) in place over the pool, you can now thread the cable through the grommets or loops around the edge of the cover. Insert the cable into the winch and pull it tight to secure the cover. Try to tuck in any extra material that is hanging down to prevent wind from getting up under the cover.
How many people do you need to put on a solar cover?
Installation is very simple since solar covers simply lay on the surface of the pool and are not attached to the pool frame or deck. You may need two people to put on and take off the cover, especially the larger sizes.
What is a wall bag for an above ground pool?
Above ground pool, wall bags are filled with water and lie on top of the cover around the inside perimeter of the pool. These bags have grommets so that you can secure them with the same cable used for your winter cover. Another option is pool cover clips which grip the top rail of the pool and hold the cover in place.
How big is a 28 ft round pool cover?
For instance, if you have a 28 ft round above ground pool, then the cover size would be 32 ft round which gives you a 2 foot overlap all the way around. You’ll need this extra material because the winter cover will dip down inside the pool due to the lowered water level and then overlap the pool wall. Adjust the cover as needed to make it even all …
Why does my pool cover keep flapping?
As the cover keeps flapping due to the wind, the material is weakened. In high wind areas, it is a good idea to take extra precautions. There are a number of handy products to help minimize wind damage. Above ground pool, wall bags are filled with water and lie on top of the cover around the inside perimeter of the pool.
How to stop water from leaking from self drilling screws?
The self-drilling screws will have made their own threads into the 1/2" pipe and should prevent any water from leaking into the pipe around the screws. If you remove them, you will need to caulk the holes. Start at one end with the clips. Work your way to the other end.
How to attach solar cover to 1/2" pipe?
Snap a clip on to the solar cover so it fits onto the 1/2" pipe below. This will sandwich the solar cover between the 1/2" pipe and the 1" clip piece.
What size PVC pipe do I need for solar panels?
You will also need some 1 inch diameter SCH-40 P VC Pipe. I used about 2′ total length cut into sections as giant washers/clips to attach the solar cover to the 1/2" pipe.
How do solar blankets work?
A solar blanket is a giant "bubble-wrap" cover that floats on the top of the water in your swimming pool. It provides a number of benefits: 1 Heats the water with the sun – so its more comfortable and it extends the swimming season 2 Reduces evaporation which saves on water refilling 3 Blocks some of the UV light that destroys the chlorine in the water so you don’t have to add as many pool chemicals. 4 Helps keep the heat in at night when the temperature drops, especially important in desert areas. 5 Keeps dirt, birds, and other items out of the pool so your water stays cleaner and helps reduce TDS (Total Dissolved Solids) – which delays having to drain and refill your pool water.
What happens if you don’t spray paint plastic?
If you want to skip the spray paint, the plastic will probably turn a dark brown or black in a couple of months of being in the sun. It probably won’t affect the strength of the clip.
How to cut 1" diameter pipe?
Cut the 1" diameter pipe to length with a hacksaw. I used 4 and 6" lengths. You could make longer if you have a band saw or table saw to cut the ripped out sections with.
How many holes do you drill in a clip?
Drill 2 holes in the clips about 3/4" from each end.
How to dispose of Oasis solar cover off-cuts?
If your local council facility can process LDPE (category 4), you can put offcuts straight into your recycling bin. If you are unsure, give them a call first to confirm.
How to get rid of wrinkles on pool cover?
If you can, leave it in the sun for a couple of hours to give the cover time to ‘relax’. When it is ready, smooth the cover out, over the pool surface, getting rid of wrinkles and air pockets. Smoothing it with a pool broom often helps. Once flattened, you can start trimming to shape with a pair of sharp scissors.
How long does it take for a pool cover to lose length?
It is possible for a cover to lose around 10% in length within the first couple of weeks - this is allowed for on a new cover, so bear it in mind, and do not cut too much off thinking the cover is too big. Remove the cover from the box, and lay it next to the pool.
What to do if playback doesn’t begin?
If playback doesn’t begin shortly, try restarting your device.
Where to hold pool cover when trimming?
If you have someone to help, ask them to hold the cover still, at the opposite side of the pool to where you are working. While you are trimming, it is important to keep checking behind you and in front, to make sure the cover does not move.
How to secure a tarp to PVC pipe?
Lay one end of the tarp over one run of the PVC pipe and secure it to the PVC using the waterproof string. Tie the string through each hole and around the PVC pipe until the tarp is tightly secured to the PVC. Next, you want to repeat the same steps for the opposite end of the tarp.
How to measure for a PVC tarp?
Step 1 – Measure Your Pool. The first step is to take measurements of your pool. Measure the length of the pool and add 6 inches to the measurement for the PVC. Next, measure the width of the pool for the size of the tarp.
How does a solar pool cover work?
A solar pool cover works by utilizing solar rays and the heat from the sun to naturally warm your swimming pool. As well, solar covers keep your pool cleaner by blocking dirt and debris from entering your pool and prevent water evaporation as well.
What is the purpose of articles being reviewed?
To ensure our content is always up-to-date with current information, best practices, and professional advice, articles are routinely reviewed by industry experts with years of hands-on experience.