[tp widget="default/tpw_default.php"]

how to fit a new toilet flush

0 Comments 11:27

how to fit a new toilet flush插图

How to repair a toilet that will not flush?

To fix a toilet that won’t flush:Unclog the toiletOpen the toilet shut off valveAdjust the toilet tank water levelReplace a warped/worn out flapperFix a loose toilet handleUnclog the rim holes/siphon jetAdjust the length of the flapper chain

How to install a new flush valve in your toilet?

Unscrew the spud nut with a spud wrench or a pair of slip joint pliers and remove the old flush valve.Slide the cone washer onto the tailpiece of the new flush valve – the beveled side of the cone washer should point toward the end of the tailpiece.Insert the flush valve into the tank opening so that the overflow pipe faces the fill valve.

What is the proper way to flush a toilet?

Take the flapper to your local hardware store to find a match. …Slide the new flapper’s rubber hooks onto the tube’s ear,then attach the flush chain. …If your toilet still won’t flush or flushes weakly,you might have a clog,need to adjust the water level,or have a problem that requires a professional plumber.

How do I get my toilet to flush?

Turn off the water to the toilet. …Flush the toilet and hold the handle down to remove as much water as possible.Remove the toilet tank lid and put it away.Use a sponge to soak up the water at the bottom of the bowl. …As you do this,you can insert your finger in the siphon jet just to feel the extent of the calcium build up. …More items…

How to add a cistern to a pan?

Adding the cistern to the pan. For this you’ll need a rubber donut washer and two fixing clamps with rubber sealing washers. These will go through the cistern and clamp into position on the panel of the pan. Step 7. Fitting the donut ring.

How to secure a flush nut?

Slot the flush into position and hand tighten the nut on the bottom to secure it. Once it is in position, tighten with a large adjustable spanner, making sure the rubber seal is nice and tight.

How to align a flush with water feed?

Align flush with water feed. Before you fit the flush, identify where the water feed will enter. The flush needs to be aligned so that the overflow is facing the opposite side of the cistern. You also need to make sure the rubber washer is in place on the bottom of the flush, inside the cistern. Step 2.

How to make sure cistern doesn’t turn?

Hold the cistern to make sure it doesn’t turn. Step 5. Put the flow top back. Pop the flow top back into position on top of the mechanism. Move it around a few times to test that it operates freely. Step 6. Adding the cistern to the pan.

How to make sure pan is sealed?

Push the pan into position, making sure a seal is created. Ensure all rims are fully sealed and pipes are in position.

Can you put a donut ring over a toilet pan?

Fitting the donut ring. If your instructions say to place the donut ring over the gap on the pan first, DO NOT do this. This is because when you lift the cistern into position it is very easy for the ring to slip or move, and the seal will not be fully secured. This will result in leaks when you flush the toilet.

How to tighten a flush valve?

Thread the mounting nut onto the flush valve tailpiece from the outside of the tank, and tighten it down with channel-lock pliers. As you tighten the nut, the beveled washer inside the tank should compress slightly, sealing the flush valve opening. Take care not to over-tighten the nut, as it is possible to break it.

How to tell if a flush valve needs to be replaced?

The clearest sign that a flush valve needs to be replaced is when water continues to run, even after the flapper and other possible causes have been addressed.

What is a toilet flush valve?

On a standard gravity-flush toilet, the flush valve is the large plastic or metal assembly that sits in the middle of the toilet tank. It is designed to control the flow of water that descends into the bowl to flush its contents into the drain system. The flush valve unit includes a long overflow tube attached to a valve seat that fits into a large opening in the bottom of the tank. The flush valve assembly also includes the flapper that seals the opening and holds water in the tank until a flush is initiated.

Why does my toilet keep running?

The reason the toilet continues to run is that the valve seat may be worn or cracked, which prevents the flapper from making a tight seal. If a toilet flapper that is in good shape doesn’t seem to seal, it’s likely that a toilet flush valve itself is cracked or worn and needs to be replaced. Although it’s more difficult than most toilet repairs, …

How to get water out of toilet tank?

Flush the toilet, then remove the toilet tank lid and use a sponge to bail out any remaining water in the bottom of the tank.

How to remove a bolt from a water tank?

Remove the nuts threaded onto the tank bolts in the bottom of the tank. As you unscrew each nut, you may need to hold the bolt in place with a screwdriver from inside the tank to keep it from spinning in place. If the nuts will not come off due to corrosion, you can cut the bolt off between the tank and the bowl, using a hacksaw blade.

Where should the flush valve be located on a tank?

Orient the flush valve unit inside the tank according to the manufacturer’s directions—usually this means the vertical overflow tube should be positioned near the back of the tank. Thread the mounting nut onto the flush valve tailpiece from the outside of the tank, and tighten it down with channel-lock pliers.

What to do if toilet wax seal is cracked?

The wax seal has cracked or broke. All you need to do is remove and reinstall the toilet with a new wax seal.

What does it mean when a toilet ring is leaking?

If it does, that points to a bad seal of the wax ring. Otherwise, one of the drain pipes may not have been glued, allowing water to leak.

How far apart should a toilet be from the wall?

1. Measure the distance from the wall to the floor bolts before removing. Standard toilets have a measurement of 12" from the wall to the floor bolts. If your toilet measures 12", you can expect to buy any standard toilet and install it comfortably in the existing location without much hassle.

How to get rid of water in toilet bowl?

Remove any leftover water in the toilet bowl and toilet basin. You can use a small cup at first, and then switch over to a heavy-duty sponge. Dump the excess water into a bucket and dispose of it somewhere safe. …

How to keep sewage fumes from wafting into bathroom?

Plug the drain opening with an old rag or another implement. This will keep the sewage fumes from wafting into your bathroom before you install the new toilet.

What do you do when you flush the toilet?

Flush the toilet to empty the basin and bowl.

How many references are there in WikiHow?

To create this article, 15 people, some anonymous, worked to edit and improve it over time. There are 8 references cited in this article, which can be found at the bottom of the page.

What are the types of toilet flush controls?

When it comes to toilet flush controls, there are typically, three types. These include the traditional lever/handle up to buttons. We won’t cover automated or sensor controls but this is the technology coming into your bathroom soon. The three main control types are:

How to replace a flush valve button?

Replacing the actual button is straightforward. Undo the mechanism by holding the back nut with one hand and then carefully unscrew it. Make sure the full and half flush rods line up with the paddles at the top of the flush valve, and then secure it in place.

How to remove a button flush?

To remove your old button flush mechanism, you should be able to unscrew it by hand. There will be a plastic nut at the bottom of the cistern that holds the mechanism in place. If it’s tight, use some pliers to loosen it. Then, the old system should lift away.

How to remove a cistern handle?

Now that it’s unchained, you need to remove the mounting nut that holds the handle in place, it’ll be either metal or plastic at the top of the cistern, on the inside. Try twisting the nut by hand to see if you can loosen it or use a pair of pliers. Unscrew the nut, as well as the black O-ring if it isn’t attached, and slide it down the lever to remove it.

Why won’t my toilet flush?

Your toilet may not flush properly or even at all for a number of reasons. If water comes up the bowl and doesn’t drain properly once you flush, you have a blockage. However, if the water in the toilet bowl is at its usual level, but water doesn’t flow down from the cistern, then the problem lies in the cistern flush mechanism. You may have one of the following issues: 1 Low water level in the cistern/tank 2 Faulty flushing mechanism 3 Broken toilet handle 4 Flush link not properly connected

Why is my toilet not flushing?

Your toilet may not flush properly or even at all for a number of reasons. If water comes up the bowl and doesn’t drain properly once you flush, you have a blockage. However, if the water in the toilet bowl is at its usual level, but water doesn’t flow down from the cistern, then the problem lies in the cistern flush mechanism.

How much slack does a toilet chain need?

Attach the chain to the lever – there’ll be a few holes for this – so there’s about 2.5 cm or an inch of slack. If you don’t leave this much slack on the chain, the toilet may not flush properly.

How to make a toilet easier to install?

That means you have to cut off the protruding ends later with a hacksaw. But first connect the water line, flush the toilet a couple of times and check for leaks. Leaving the bolts uncut until you’ve done these final checks lets you easily remove and reset the toilet if you find any problems.

What does a toilet bolt look like?

Some metal toilet bolts have a yellowish zinc coating that makes them look like brass. So check the label and make sure you’re getting brass bolts and nuts. They won’t rust away and they’re easier to cut off later. If you need to reanchor the toilet flange, buy stainless steel screws. They won’t corrode like steel or break off like brass while you’re driving them.

Why does my toilet rock?

If the flange is loose or damaged , the toilet will rock. And a rocking toilet will distort the wax ring and cause leaks. So be sure to scrape off the old wax ring and inspect the flange. Here are some solutions for broken, corroded or loose flanges.

How to fix rot under toilet flange?

The best solution depends on the extent of the rot. If the rot is only under the flange, use an ear-type repair ring. The ears let you drive screws into firm wood farther away from the flange. Before you install this kind of ring, hold it up to the drain horn on the underside of the toilet.

How to measure for a new toilet?

from the wall. But with a few models, that measurement is 10 in. or 14 in. To check the rough-in, just measure from the wall to the toilet’s hold-down bolts. If that measurement (plus the thickness of the baseboard) isn’t approximately 12 in., toilet shopping will be a bit harder. Most home centers carry only one or two 10-in. models and no 14-in. models. If you have to special-order a toilet, be prepared to spend much more. If there’s a door near the toilet, also measure how far the bowl protrudes from the wall. If you are replacing a toilet with a standard bowl with an “elongated” model, the door may not close. Read on to learn how to install a toilet.

How to check rough in on a toilet?

To check the rough-in, just measure from the wall to the toilet’s hold-down bolts. If that measurement (plus the thickness of the baseboard) isn’t approximately 12 in., toilet shopping will be a bit harder. Most home centers carry only one or two 10-in. models and no 14-in. models.

How to avoid last minute shopping trips?

Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.

How to remove a flush valve?

Locate and remove the flush valve. Locate the thick, conical rubber gasket and remove it. Underneath the gasket you’ll see a large plastic nut. Loosen and remove the plastic nut to remove the flush valve. Start to loosen the nut by turning it counterclockwise with your pliers. The flush valve will come right off.

What happens if the toilet valve stops working?

If the flush valve on your toilet stops working properly or you have a leak, it can be time to replace the flush valve. Although plumbing work can seem like a job best left to the experts, you can replace the flush valve on your toilet with minimal hassle by following some simple steps. Steps.

How to adjust the filler valve in a toilet?

The water level should usually line up with the water mark on the inside of the toilet bowl. If water does not rise to the right level in the toilet, adjust the filler valve. You can adjust the filler valve dramatically by moving the entire valve up or down.

How to fix a toilet that is leaking?

1. Make sure the toilet is not leaky. Flush the toilet a few times to check for potential leaks that may have developed. If the toilet has a leak, it will leak immediately. Get under the toilet with a flashlight and see if the toilet is dripping. Identify where the leak is coming from.

What does it mean when a flapper valve is not closing?

If you hear a whistle or noise that sounds like air leaving a balloon, then the flapper valve is not closing. Make an adjustment to slightly raise or lower the valve. The screw for the flapper valve is usually found on the float that looks like a little barrel that moves up and down with the water level.

Where is the supply hose on a toilet?

The supply hose located on the bottom of the toilet tank should be reattached to the toilet at this point, to restore water flow. It has a plastic nut on the end with threads. Connect it to the filler valve (looks like a little white tube) by threading the nut and bolt by hand.

How to stop water from spilling out of toilet?

Flushing the toilet will drain most of the remaining water from the toilet, allowing you to access the its internal parts more easily. This will also prevent any remaining water from spilling out of the toilet and all over the floor. Soak up any remaining water with a sponge and bucket.

What is a close coupled toilet?

A close coupled toilet is one of the most common designs you’ll find in bathrooms up and down the UK. The cistern is situated directly above the pan and is “closely coupled” together – hence the name. Some of the best bathrooms tend to have a toilet that is designed to match the rest of the suite. Some, even have smaller toilet dimensions, to make optimum use of space.

When to unpack toilet?

Before you do anything. Always unpack your toilet immediately after delivery. Check for any damage or faults as it’s better to find them now, rather than during installation. Always turn off your water at the mains before attempting any DIY in the bathroom.

Can you add videos to your watch history?

Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

How to flush a toilet that won’t flush?

Open the tank and locate the float and the fill line. Activate the flush while keeping the lid open and watch the water release into the toilet bowl and then fill back up. Check to see if the tube stops refilling before the float reaches the fill line. If it does, the toilet won’t perform a fully efficient flush. Adjusting the float is pretty easy—you have to position it to connect it to the refill tube. Now, flush again and see if it is working correctly.

How to improve toilet flushing efficiency?

First, open the tank lid and remove the fill hose that varies by toilet models. Now, put a funnel inside the overflow tube carefully, and fill it with vinegar .

How to clean a toilet with a clogged jet?

To clear this up, use a heavily watered-down bleach or a vinegar solution and an old toothbrush or wire brush to sc rub away the blockage and obstruction on the nozzles . When you are finished, clean the toilet thoroughly with bleach or a standard toilet bowl cleaner.

Why is it important to flush toilets?

Since a powerful flush forces waste down the drain in one go and stops it from coming back up, it is essential to keeping your toilet clean and hygienic. A strong flush also saves you from having to flush the toilet multiple times. Toilets that require multiple flushes are considered a weak and less desirable choice.

Why is my toilet not flushing?

Sometimes low water in the tank can cause a weak flushing toilet. Other times clogged holes around the rim can lead to a weak flush performance. Either way, here are some quick tips to help get rid of the problem and boost the flushing power of your toilet.

What is vacuum assisted toilet?

Vacuum-assisted toilets contain plastic tanks that generate suction action in the tank as the water releases while sucking the waste out of the bowl, generating a lot more flushing power than conventional toilets.

How does water enter the toilet?

Water enters the toilet bowl through several jet holes that are located around the upper rim. These jets control the pressure and the flow of water as it flows into the bowl. The flow of the water creates the centrifugal force required to boost the efficiency of the flush.

What to do if a toilet nut is stripped?

If the nut inside your toilet is stripped, use a hacksaw to cut through it.

How does wikihow mark an article as reader approved?

wikiHow marks an article as reader-approved once it receives enough positive feedback. In this case, 100% of readers who voted found the article helpful, earning it our reader-approved status.

How long does it take to replace a toilet handle?

Toilet handles are easy to remove and install on your own in around 15 minutes. All you need to do is unscrew the old handle and then put the new handle in its place. Once you install the new handle, you might have to make some slight adjustments so it doesn’t get stuck. When you’re finished, your toilet will work like new!

What to do if toilet handle doesn’t work?

If the new handle still doesn’t work after you install it, contact a plumber to find the problem with your toilet.

How to undo a toilet flapper?

Undo the chain clip attached to the lever. The chain clip attaches the handle to the flapper and lets you flush your toilet. Look for the section of chain clasped to the end of the metal or plastic lever that connects to the handle. Undo the clasp to detach the handle and lever from the rest of your toilet.

How to loosen a tank handle?

Locate the plastic or metal mounting nut that’s holding your handle in place on the inside the top of the tank. Try twisting the nut clockwise by hand to see if you can loosen it. If not, grip the nut with a pair of locking pliers to get better leverage on it.

What to do if your toilet doesn’t flush?

If your toilet doesn’t flush at all, make sure the chain clip is attached to the lever properly.

How to tighten a toilet fill valve?

Tighten the fill valve nut carefully. When you have the toilet fill valve in place, the final part of its installation is to tighten a lock nut onto the threaded part of the valve. This is located on the underside of the tank. When doing this, it is important not to tighten the nut too hard. The nut should be tightened by hand to ensure that you don’t tighten it too much.

What is the float on a toilet?

In newer toilets, it is the entire plastic column that includes the float and the on-off lever for filling. In older toilets, the float is a separate piece but it will be connected to the top of the fill valve. The fill valve also has a tube attached to it that connects to the overflow pipe.

How to get water flowing again after replacing fill valve?

Once the replacement fill valve is in place, it’s time to get the water flowing again. Attach the supply line to the bottom of the new fill valve. Make sure that there is a washer inside the end of the supply line and tighten it with a wrench until it’s tight.

What would crack a toilet tank?

Tightening the nut on the bottom of the fill valve with a wrench or pliers could crack the toilet tank or the valve.

Where should washers be on a tank?

There should be washers on the inside and the outside of the tank where the fill valve goes through it.

How to stop water from flooding?

It’s a good idea to turn off your main water valve, as well. Find the main water shut-off valve on the outside of your home and turn it off. Then, go around your property and turn on various fixtures to confirm that they’re off, but it will also drain off residual water that’s inside the system. Doing this will help you avoid water damage due to a flood.

Where is the water valve located on a toilet?

You should have a water valve directly below the toilet tank. It should be located between where the water pipe comes out of the wall and where it attaches to the bottom of the toilet tank . In most cases, you will turn the water shutoff valve clockwise to turn it off.

Related Post