[tp widget="default/tpw_default.php"]

how grease fittings work

0 Comments 02:48

how grease fittings work插图

One?way check valve
Grease zerk fittings work by acting as aone?way check valvethat allows grease to pass through one way,but not the other. Inside the fitting is a ball check suspended by a spring. As grease is pushed into the fitting,pressure is created against the ball check that compresses the spring allowing grease to pass completely through the fitting.

How often to grease the "fittings"?

How often should you grease fittings? Extremely Wet and Muddy Conditions – Lubricate machine grease fittings (A) every 10 hours of operation or on a daily basis. All Other Conditions – Lubricate machine grease fittings every 50 hours of operation. Do you have to grease new ball joints? You have to grease it yourself.

What are these grease fittings to be used on?

Grease fittings, sometimes called grease nipples or Zerks, are small hydraulic check valves used on bearings and similar mechanical assemblies to supply lubricant to internal parts.They are standardized in the US under SAE J-534 for automobiles and under SAE 35411 for aerospace applications.

How to get grease off of my fridge?

Method 3 of 3: Removing Stubborn and Burnt Grease StainsMix baking soda and water. In a bowl,combine equal parts baking soda and water. …Rest the mixture on the stained area for 15 minutes. …Scrub the stain using a nylon brush. …Rinse off the surface. …Pour vinegar over the stain. …Scrub the stain again. …Rinse off the vinegar. …Dry the steel with a soft towel. …

Can You Grease balljoints without grease fittings?

This is after the ball joint is installed. Those needles for grease guns are for tiny tiny grease fittings, such as those you find on small heim joints, not injecting grease into a boot. If the joint doesn’t have a fitting, you are never going to get grease to go into it.

How do grease fittings work?

Grease zerk fittings work by acting as a one?way check valve that allows grease to pass through one way, but not the other. Inside the fitting is a ball check suspended by a spring. As grease is pushed into the fitting, pressure is created against the ball check that compresses the spring allowing grease to pass completely through the fitting. When grease flow stops, the spring pushes the ball check back to its original position, closing the fitting and preventing grease to escape.

What is the most common standard size grease fitting?

The most common standard grease fitting size is 1/4"?28 SAE?LT and is often used in automotive applications. They can also be found in agricultural environments as well as other various standard duty applications. For heavy duty applications, larger 1/8"?27 PTF zerk fittings can be found.

How much grease should I put on a fitting?

The amount of grease put in a fitting depends on the size of the part to which it is attached. As a general rule of thumb, apply grease until you begin to feel resistance while pumping. Do not apply grease until it seeps out of bearing seals or other components.

What are the different types of grease guns?

There are many different types and designs of grease guns, and we offer lever, pistol, cordless, and pneumatic grease guns. We have a gun for practically any application. G.L. Huyett offers the following on our site.

How to attach grease gun to zerk fitting?

First, ensure both the zerk fitting and the grease gun coupler are clean and free of debris and other contaminates. This will help ensure a secure connection between the fitting and the coupler. Next inspect the fitting to ensure there is no damage.

What is a grease zerk?

Intended for light oils and hydraulic fluids, leak?proof grease zerks are often used in the textile and food processing industries where prevent lubricant leakage is critical. Available in zinc clear, zinc yellow, or traditional steel finish. Designed to provide leak?proof seals up to 10,000 psi.

What is a button head grease fitting?

Button head grease fittings are a heavier duty fitting identified by their flat, low profile appearance. They are able to handle large grease volume due to their high flow rate and sturdy construction. They are commonly used on conveyors, mining equipment, agricultural equipment, and other rugged applications.

How Do Grease Line Fittings Work?

Although there are numerous types of grease fittings, they all work based on roughly the same principle. Like other oil lubrication fittings, they are installed on the bearing or other part they are intended to lubricate. The fitting has a valve, typically a spring-tension ball valve.

Types of Lubrication Fittings for Oil and Grease

There are several different types of grease and oil lubrication fittings, each with its own unique benefits. At DropsA USA, we offer compression fittings, grease nipples, snap on fittings, pipe clips, push-in fittings and anchor blocks.

Order Your Grease Fittings Today

As leading industrial lubrication specialists we offer a variety of oil and grease line fittings for your auto lube systems. Whatever your requirements may be, we have lubrication solutions that can work for you. Explore our selection of fittings to find the right option for your needs today.

What is grease packed around wheel bearings?

Thick bearing grease is packed all around the wheel bearings every time they’re replaced or even when they’re removed for wheel hub or axle service. Grease caps protect the bearing grease from contamination and also hold the grease that surrounds the wheel bearings in place.

What are grease caps used for?

Grease caps are the small, round, metal covers you see at the very center of a wheel. Sometimes they’re called dust caps, but for clarity, we’ll call them grease caps from this point forward. Grease caps protect your wheel bearings from the dirt, dust, sand, water, salt and road grime that can (and will) destroy bearings. Without grease caps, your wheel bearings simply wouldn’t survive for very long out on the road.

Why are bearing caps packed with grease?

This serves two purposes. It provides a continuous supply of grease for the bearings, and it also keeps the grease from migrating away. If the cap were empty, the grease might eventually work its way into the cap, filling the cap but leaving the bearings dry .

How often should you clean trailer wheel bearings?

The trailer wheel bearings should be removed, cleaned and repacked with grease at least once each year. If you’re pulling a boat trailer, especially a trailer that’s exposed to saltwater, it’s a good idea to do this at least twice each year [source: Trailer Parts Warehouse ] .

How to prevent grease caps from getting damaged?

One way to prevent damage to your grease caps (aside from knowing if the caps are the press-on or screw on-type) is to buy the proper tool to remove them. A lot of grease caps are damaged by people prying the caps away from the wheel hub with a screwdriver or similar tool.

Can grease be contaminated?

Wheel bearing grease can easily be contaminated, resulting in bearing failure. Grease caps protect the bearings (and the grease) from the stuff that destroys bearings. Loretta Hostettler/ iStockphoto.

Is it expensive to replace bearing caps?

The good news is that they’re not expensive – they’re usually only a few dollars each. The bad news is that you’ll need to get a new cap before you go anywhere. If you allow the bearings to be exposed for any amount of time, you’re risking contamination that can destroy the bearings.

What do grease guns dispense into?

Dispense from grease guns into grease fittings and bare lubrication points.

What is a secure fit in unthreaded holes?

Ensure a secure fit in unthreaded holes— these fittings cut threads as they’re installed. Use these fittings in tight spaces where protruding fittings won’t work.

What is rigid tip adapter?

These rigid tip adapters penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

What is a T-shaped top?

Often used on earth movers, mining equipment, and other heavy machinery, these fittings have a T-shaped top that holds the dispensing tip in place so it won’t pop off when adding grease.

How to expose a flexible nozzle?

Slide the metal sleeve up to the tip for rigidity. Slide it back down to expose the flexible nozzle.

Where are pressure relief valves installed?

Less than a quarter of the height of standard pressure-relief valves, these are often installed on tanks in low-clearance areas.

Related Post