[tp widget="default/tpw_default.php"]

how do you fit a door handle

0 Comments 20:39

how do you fit a door handle插图

How to fit the door handleUse the handle’s face plate to trace the outline with a pencil.Consult the template for the faceplate depth and chisel this part of the door out.Screw the faceplate into the side of the door.Place the door handles into the holes and check for alignment.Once everything is aligned drill the handles into place and check to see if they work.More items

How to properly install door knobs and levers?

If your cabinet doors have stiles (also called framing),cabinet pulls are usually 2 to 3 inches up from the bottom edge of the door. …If your cabinets have slab doors without stiles,cabinet pulls are usually 2 to 3 inches up from the bottom edge of the door. …Measure and mark this location with a pencil.More items…

How do you put the handle on the door?

When it comes to installing cabinet door handles (either knobs or pulls), they are always placed on the opposite side from the door hinges. You’ll specifically want to place them anywhere between 1’’ and 4’’ from the top or bottom edge of the door. Anywhere within this range will work as it is based on personal preference.

How to install a standard door knob?

The long metal piece sticking out of the exterior knob is called the spindle. …Install both knobs by sliding the spindle through the slot in the latch.Align the two long screws from the inside knob into the cylinders on the exterior door knob and tighten the screws.More items…

How to install or replace door hinges?

Drill pilot holes where you marked the screw location on the doors. Go slowly so you don’t drill all the way through the door.Attach the new hinges with screws .Install new knobs and catches or reattach the old ones.

How to chisel out a faceplate?

2. Chisel out the faceplate outline with a chisel and hammer. Place the chisel at a 45° angle and begin to chisel the outline from the top, chiselling to the depth specified in your instructions. Use the pressure of the chisel and your hand to remove all of the wood within your outline.

What to do if faceplate does not fit?

If the faceplate does not fit flush with the narrow part of the door, make adjustments with your chisel until it does. Faceplates come in different depths, so it is important to follow your kit’s instructions when chiselling the narrow part of the door. Screw the faceplate into the narrow part of the door.

Why is it important to secure a door?

Securing the door is a very important step, as it will allow you to drill necessary holes without damaging anything.

How to attach a door handle kit to a door?

Attach the door handle kit’s template to the door. Using masking tape to secure the template to the door, make marks on the template showing where you will drill. Make these marks on the narrow part and on both outer sides of the door, being as accurate as possible.

How to measure for a door handle?

1. Measure 41 inches (100 cm) from the floor. Although you could follow the directions that come with your handle instructions, the most common placement for a door handle is 41 inches (100 cm). Place the end of a tape measure on the floor and mark the narrow portion of your door with a pencil. You can also measure the height …

Which part of a door is harder to drill?

The narrow part of the door is more difficult to drill into, as it has a smaller surface area. Take extra care when drilling this hole.

How to slide a latch in?

In order for your latch to slide in, the hole must be chiseled into a square. Make sure you use a long thin chisel for this part. You should end up with a square hole (as in the diagram below). You should be able to see the handle spindle holes drilled previously through this hole.

How to drill out a striker plate?

Use a spade drill bit to drill out the striker plate hole location.

What is a chisel for latch?

Chisels are needed for carving out the hole where your latch, and latch striker plate will go. When it comes to chisels, Irvin Marples is a premium brand. They have a sturdy neck and excellent shock absorption. Each blade is forged in one piece, and hardened and tempered to last a very long time.

What part of the latch do you mark?

You then need to mark the outer part of the latch, and the inner part .

Do you need spade bits for wood?

You will need spade (flat) wood drill bits in particular. But it may be worth you buying a drill set like the one below that offers a wide variety of drill bits and sizes for most household DIY tasks.

Can you mark wood with a pencil?

Marking wood can sometimes be diffulcult to mark using a standard pencil. Mark up your work easily using these carpenters pencils.

Recommended equipment

Below is a list of tools and equipment useful in fitting handles to an interior door:

1 – Measure the door

We recommend following the manufacturers fitting instructions for more information on handle placement. Typically, you are looking at around 990mm high, but this can also depend on how tall your door is. Use a tape measure and mark with a pencil on the narrow section of your interior door the advised height.

2 – Secure door handle template to door

With the door measured and marked, attach the door handle template using masking tape. All door handle templates are different, but will all indicate where you will need to drill and chisel. Use the pencil to mark the required drilling and chisel areas on the narrow section and both outer sections of the door.

3 – Drill pilot holes

It is always best practice to drill pilot holes first; it makes it much easier to drill screws in later on and reduces the chance of the wood splitting. Use a 2mm drill bit, and then use the fitting instructions to find out how big the holes need to be to fit the handle and faceplate screws.

4 – Drill 25mm spade holes

You will also be required to drill 25mm spade holes for the spindle as advised by the template.

5 – Chisel out the faceplate

With all the holes prepared in parts three and four, we can now concentrate on attaching the faceplate to the narrow section of the door. Hold the faceplate in the place where you eventually want it to go, and then trace an outline with the pencil.

6 – Fit the faceplate

Secure the faceplate using the screws provided with the door handle. As stated in step three further up, use pilot holes to make this process easier.

How to chisel out a hole in a door?

Use the sharp chisel and the hammer to chisel out a hole for the latch. The cuts made with the utility knife are your guidelines as to where to stop chiselling. Also, chisel inside the hole for the latch to fit. Insert the latch into the side of the door to see if its faceplate sits flush to the door. If it doesn’t, chisel some more until it does sit flush.

How to drill a hole in a door frame?

Using the mark where the middle of the barrel is, drill a pilot hole in the centre on the inside of the door frame. Then attach the 25mm spade bit to the cordless drill and drill into the pilot hole.

How to stop chiselling?

The cuts made with the utility knife are your guidelines as to where to stop chiselling. Also, chisel inside the hole for the latch to fit. Insert the latch into the side of the door to see if its faceplate sits flush to the door. If it doesn’t, chisel some more until it does sit flush.

How high should a door handle be?

Alternatively, you can read the instructions that come with the door handle kit and use that height. Or you can use the standard height for a handle, which is 1050mm off the floor. After deciding the height of your door handle, measure and mark it on the side of the door. Before you start installing the door handle, place a door wedge under the door to stop it from moving while you’re working. Move the wedge as you change the side of the door you’re working on.

How to draw a striker plate?

Line it up with the top and bottom lines you drew on the side of the door frame. Use a pencil to draw around the striker plate. Remove the striker plate from the door. Use the utility knife to cut around the outline of the striker plate.

Where to put striker plate on door?

To work out where to install the striker plate, almost close the door and mark on the door frame, where the middle of the barrel is. Hold the striker plate against the door frame, so that it’s in the centre of the latch. Mark the top and bottom of the striker plate on the door frame.

Is asbestos a health hazard?

Asbestos, lead-based paints and copper chromium arsenic (CCA) treated timber are health hazards you need to look out for when renovating older homes. These substances can easily be disturbed when renovating and exposure to them can cause a range of life-threatening diseases and conditions including cancer. For information on the dangers of asbestos, lead-based paint and CCA treated timber and tips for dealing with these materials contact your local council’s Environmental Health Officer or visit our Health & Safety page.

How to drill out a 4th hole on a jig?

Then you need to drill out the first and the fourth hole on the jig using a 3mm drill bit.

What is a handle hole drill jig?

Using the Handle Hole Drilling Jig is one way of ensuring a professional finish and it’s a quick and accurate way of getting the handle holes in the right position.

How far from the top of a door should the handle be?

Measure from the top of the door (if a base unit door) to the centre of the top hole position. In this example we decided the top hole for our handle would be 55mm from the top of the door.

How to mark a door of the opposite hand?

To mark a door of the opposite hand, simply turn the jig around. to mark a wall unit door simply flip it over. Once the jig is set up you can do all the marking of the holes literally in a few minutes saving lots of time.

Why do we brake a jig?

The reason we would do that is because the jig is very useful for helping to mark the handle position from the edge of the drawer.

How far should the first hole be from the edge of the door?

Therefore the first hole wants to be 250mm from the edge of the door.

Where to drill a door handle?

Always drill from the front through to the back of the door . The reason for this, is that if you drill from the back of the door through to the front, the holes could end up in the wrong position if the drill is even slightly out of level – making fitting the handle impossible.

A step by step guide to how to fit door handles

More and more homeowners are choosing to try their hands at DIY these days, but even deceptively simple tasks such as fitting interior door handles can come across to the inexperienced and butter fingered amongst us as completely bewildering.

What tools will I need?

Pencil or Pen, Hammer, Screwdriver with various heads, Wood Chisel, Tape Measure, Drill, Spade bit, Drill bits, Set Square, Dust Sheets, Tape.

The Steps

They always say ‘measure twice and cut once’ and the same is true here. Your measurements and markings are a vital first step that you really want to get spot on.

How to measure a door handle?

Choose a new door handle that fits on your door. Use a tape measure to measure from the inside edge of the door to the center of the hole in the door to get the backset measurement, then choose a handle that fits this backset.

How big is a door handle backset?

Most door handles have a standard backset of 60 mm or 70 mm, so you shouldn’t have any trouble finding a new door handle that fits in the existing holes in your door.

What is the latch on a door?

The latch is the angled metal piece that moves in and out of the hole on the inside edge of the door. When you close the door, this latch hooks into a hole in the door frame to keep the door closed. Turning the door handle moves this latch in, so you can open the door.

How to put a cover plate on a car?

Put the cover plates in place on top of the inner plates. Slide the new cover plates on and press them against the inner plates until they snap into place. Attach any provided screws that hold the plates in place using your screwdriver.

What to use if you don’t have a door stop?

If you don’t have a door stop, you could use a wedge-shaped piece of wood or any other wedge-like object you can find around your home that will fit under the door.

Where are the inner plates on a door?

Take out the screws that hold the inner plates in place on either side of the door . The inner plates are what sit directly under the cover plates you just removed. These hold the door handle’s latching mechanism in place inside the hole in the door.

Can a door handle latch fit in a recess?

Door handle latches come in a standard size, so the new latch should fit into the old recess without any problems. If it doesn’t seem to fit for some reason, you can use a chisel to make adjustments to the depth and shape of the recess in the door.

What does taking a note of all these door measurements do?

Taking a note of all these door measurements will ensure that you can choose the right lock latch and door handle to suit the door perfectly first time.

Why do you need a shorter backset on a door?

We recommend that a shorter backset is chosen when a door is glazed to avoid the latch mechanism meeting the rebate of the glass.

How thick is a fire door handle?

Many internal doors are commonly made to 35mm Thickness. A standard FD30 Fire Door is usually 44mm Thickness.

What is the standard height of a door?

The standard height of a door is usually either 1981mm (78"), or occasionally 2032mm (80") or 2040mm. Once again there are always custom-sized doors, especially in older properties.

Related Post